Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
Are you hunting for critical information concerning How to Install a Bathtub Yourself?
Mounting a tub isn't exactly brain surgery, but it does call for strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old tub is readily easily accessible, the job can relocate immediately; if you have to open up a wall to remove the old bathtub and place the new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as embeded in the new one. Make sure you have certified yourself for the task and fit attempting it. Instead of hiring a service provider to take over a halfway-completed task, it is better to take into consideration employing one prior to you start. Opportunities are you may need an expert plumber to make tube links.
This write-up will certainly help you install a new tub in your shower room if you have actually currently purchased a brand-new tub and don't require to transform the arrangement of your previous supply of water pipelines.
Your devices and material list need to comprise the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is detach the water system. After doing so, activate the faucets to drain any water staying in the system. The procedure of eliminating the existing faucets can be fairly bothersome as a result of the restricted access that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will originate from the pipes. When the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
Prior to carrying on to fit the new taps, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Protect the faucet in place with the producer provided backnut. As soon as the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former kind ought to be attached to the tap ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Making use of the two wood boards under its feet, place the tub in the required setting. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next goal is to make sure that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the tub till the spirit level reads degree.
To install taps, fit all-time low of the furthest versatile faucet connector to the proper supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the supply of water as well as examine all joints and brand-new pipework for leakages as well as tighten them if necessary. Fill up the bath tub and additionally check the overflow electrical outlet and also the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait until the tub has actually been made use of at least when as this will certainly settle it into its last position.
Getting ready for the Setup
To start with, the supporting framework provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to prevent strain on the tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last position.
Tiling Around the Bath tub
In the location where the bath fulfills the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to crack a rigid seal, causing the water to pass through the wall surface in between the bath and also the tiling, bring about difficulties with moisture as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and also installations. They are sold in tubes and cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealer can break fairly very early if you do not take into consideration this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly available on the marketplace. It is recommended to fit the tiles making use of water-resistant or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our post about How to Install a Bathtub. Thank you for taking the time to browse our piece of content. Are you aware of somebody who is interested in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Feel free to promote it. Kudos for your time. Visit us again soon.
Booking Report this page